Methods to Construct a Workbench. Straightforward, Low cost & Sturdy.

Share it with your friends Like

#workbench #cheapworkbench #buildaworkbench
http://diyforknuckleheads.com Methods to Construct a Low cost Sturdy Workbench on your Storage. A workbench is a should on your storage or shed. With regards to constructing a workbench l wanted to fulfill three standards. The workbench was required to be robust, low cost to construct (second hand or reclaimed supplies are superb. It does not should look fairly as fairly quickly it’s going to be trashed) and durable sufficient to take a beating with out falling to bits.

Earlier than l go on…

DIY For Knuckleheads Web site: https://diyforknuckleheads.com

————-

SUBSCRIBE to DIY For Knuckleheads and by no means miss a video once more!
http://www.youtube.com/consumer/shaneconlan1

————-

Instruments l Use: https://diyforknuckleheads.com/tools-resources/

————-

Mailing Handle:

DIY For Knuckleheads
P.O. Field 152
Sawtell,
NSW, 2452
Australia.

————-

Take a look at the Newest Swag from our New DIY For Knuckleheads Clothes and Accessorie Retailer!
https://store.spreadshirt.com.au/DIYForKnuckleheads/

————

Verify us out on Fb;
https://www.fb.com/DiyForKnuckleheads/

———-

Music equipped by Jason Shaw at www.audionautix.com
Launched beneath Artistic Commons License three.zero.
Music Titles: Jennys Theme and Banjo Quick

Instruments and Supplies Required for this Challenge. Bench approx. 2.2 metres lengthy, 700mm huge and 1.zero metre excessive.

For the legs: 90mm x 35mm (four x 1½”) pine. Two at three.6metres (approx 11′ 12″. I feel that reads 11 ft, 12 inches)
For the body: 90mm x 35mm (four” x 1 ½”) Eight at 2.4metres (eight ft)
For the sting trimming: 42mm x 19mm dressed pine. Six at 2.4metres (eight ft)
Ply for bench high and shelf: One sheet at 2.4metres (eight ft) x 1.2metres (47 inches) x 17mm.
Bolts for body: Eight cuphead bolts at 100mm (four inches) x 10mm with washers and nuts.
Screws to assemble the workbench: 120 x 65mm Phillips head screws.

Dimensions of Workbench:
Total width of bench high together with pine trim: 690mm (27 inches)
Total size of benchtop: 2.0metres (78 ½ inches)
Total top of workbench together with the 17mm benchtop: 900mm (35 ½ inches)
Total width of body: 570mm ( 22 ½ inches)
Total size of body: 1880mm (6′ 2 inches)
Total top of workbench leg (which incorporates the highest rail as it’s checked into the leg) 880mm (34 ½ inches)

Instruments:
Handsaw, round noticed or drop noticed.
Powered or cordless drill.
10mm (four inch) drill bit.
1/eighth countersinking drill bit.
No.2 Phillips Head bit.
Spanner to tighten nuts.
Set Sq.
Builders Sq.
Tape Measure
Pencil
Spirit Stage
Wooden employees Glue.

Cheers,
Uncle Knackers

All Movies produced by shaneconlan1’s YouTube Channel are supplied for informational functions solely.
All of the content material supplied is for common steerage solely. As a result of instruments, merchandise, supplies, gear, methods, constructing codes and native rules are continually altering, shaneconlan1 can’t, and doesn’t assume any accountability or legal responsibility for the accuracy of the data contained therein. Additional, shaneconlan1 (Shane Conlan) won’t settle for any declare for legal responsibility associated to, however not restricted to, omissions, errors, harm, injury or the end result of any undertaking. The viewer should all the time take correct security precautions and train warning when taking over any undertaking. If there are any questions or doubt regarding the aspect of a undertaking, please seek the advice of with a licensed skilled.

Comments

J J says:

Ga- rage. I love the aussies. How much did you spend on her mate?

Mbmoney1217 says:

I've watched many YT videos about building different workbenches, but this is the design I always go to. Strong, cheap, and easy to build. I've just modified the design for my needs. The core design stays the same. Cheers!

Justin Jolley says:

Hey Uncle Knackers, I've noticed in recent videos that you've put castor wheels on. Did you have to cut down the height to accommodate them or did you just screw them on as is?

Mark W says:

I used 2×6 for my top rails. Wife rolling her eyes, again!! "Why can't you ever just do it like the video shows"!? LOL!

Wood Worker says:

Hello there. I like your video very much. It's really inspiring. I'm just new. I made myself a work bench. Yeah, I had a hard time, but I did. I'm waiting for you on my channel. You can make me happy by supporting me.

Leandro Pedras says:

After watching a few videos on making a work bench, this was the most helpful for what I needed. Cheers mate!

Callix Miller says:

OK, I’m a new to these projects, so not sure where to locate that measurements/parts list. H E L P !!

Stevetube101 says:

I made this workbench, with a few mods! You can see it in my videos…

Pete Singh says:

Good job mate like down town

D G says:

I looked up Sawtell NSW out of curiosity. Looks like a fantastic place to live. Cheers!

Thomas Gillot says:

Anyone know how much USD the materials will cost for the full build?

sabestek says:

One of the better workbench builds I've seen watched on YouTube thanks

BigAl1able says:

It's pronounced Garage NOT Garage !!!

tkay4401 says:

I've watched one workbench video after another, but this is I think is the best. I love the simplicity of it. I really like the way the way you made the legs bear the weight of the rails and table top. Simple but genius! And, the trim around the edges gives it a very nice aesthetic appearance. Brilliant!

BIlly The Kid says:

This will be my next project!! Thanks brother! Great video!!!!!

Ross Kilpatrick says:

Will build this bench thanks mate for such an entertaining video. Also fun to watch and listen.

Lloyd Duston says:

Best workbench design I have found so far. And this guy's instruction is simple and straight forward. I built this bench in just a couple hours with some 2X4 lumber I had laying around. Bought the plywood for the top at Home Depot and they cut it down to size for free right there at the store. Thanks to the gentleman who did this video………OUTSTANDING!

- Elektryx - says:

Such a breath of fresh air to see a video using Metric. Great vid mate, i'll be using this to build my own 5m bench this weekend :)=

Martin Babiak says:

thanks! Just finishing workbench based on this video. I am beginner in woodworking but this table is not difficult to make and it is so sturdy! I made legs from 10x10cm which I had from my old project. Since I am beginner, my 45 degrees angles are not so perfect, butstill ok. My bench is 200x100cm. Thanks a lot for this video!

Ralph Steven says:

Nice bench, for extra top frame strength i'll add glue before screwing….

Write a comment

*

20 − 5 =